Slipcasting of MAX phase tubes for nuclear fuel cladding applications

As a proof of concept, tubes of Ti3SiC2 MAX phase were slipcast in order to investigate its potential for the fabrication of fuel cladding for nuclear reactors. A slip consisting of 46% dry weight basis (dwb) water, 4% dwb polyethyleneimine (PEI), 0.5% dwb methylcellulose was used to cast the tubes, which were then sintered for 2 h under vacuum at 1450 °C. Silicon loss was observed at surface which resulted in the formation of TiC. The hoop stress to destruction of the tubes was measured and achieved a maximum of 9.1 ± 2.2 MPa/mm of tube thickness

Laser sintering of electrophoretically deposited (EPD) Ti3SiC2 MAX phase coatings on titanium

Ti 3 SiC 2 was deposited onto titanium substrates using electrophoretic deposition; a 4.3 wt% suspension of Ti 3 SiC 2 in water at pH 9 was used with 10 V field applied across the substrates. After 10 min of deposition, the coating surface density was 1.89 ± 0.26 mg/cm 2 . The thin coatings were then rapidly densified using a Renishaw AM250 3D printing laser to scan the surface. Cross sections of the substrate post sintering, showed the coating thickness to be 10–30 μm and densified with silicon loss constrained to the surface, although the overall coverage and adhesion varies. Preliminary Raman spectroscopy results suggest some MAX phase remains after sintering, but further characterisation is required to confirm

Giant electric field tunable magnetic properties in a Co50Fe50/lead magnesium niobate-lead titanate multiferroic heterostructure

Co50Fe50/(0 1 1)-oriented lead magnesium niobate–lead titanate (PMN–PT) multiferroic (MF) heterostructures were fabricated by RF sputtering magnetic films onto PMN–PT substrates. The effect of magnetic layer thickness (30 nm to 100 nm) on the magnetoelectric (ME) coupling in the heterostructures was studied independently, due to the almost constant magnetostriction constant (λ = 40   ±   5 ppm) and similar as-grown magnetic anisotropies for all studied magnetic layer thicknesses. A record high remanence ratio (M r/M s) tunability of 95% has been demonstrated in the 65 nm Co50Fe50/PMN–PT heterostructure, corresponding to a large ME constant (α) of 2.5   ×   10−6 s m−1, when an external electric field (E-field) of 9 kV cm−1 was applied. Such an MF heterostructure provides considerable opportunities for E-field-controlled multifunctional devices

Synthesis and microstructural evolution in ternary metalloceramic Ti3SiC2 consolidated via the Maxthal 312 powder route

A bulk specimen containing Ti3SiC2, TiSi2 and TiC was prepared through an in situ spark plasma sintering/solid-liquid reaction powder metallurgy method using the Maxthal 312 (nominally-Ti3SiC2) powder as a starting material. The reaction mechanism, phase constituents and evolution of the microstructure were systematically investigated by X-ray diffraction (XRD), optical microscopy, scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS) system, transmission electron microscopy (TEM), Raman spectroscopy, differential scanning calorimetry (DSC) and Vickers microhardness testing. Phase analysis and microstructural characterization revealed that the bulk sample contained binary ancillary phases, possibly due to Si evaporation and/or carburization. The deformed microstructure around the indents revealed evidence of plasticity, intrinsic lubricity and toughening. The Microstructural and orientation relationships between the phases contained in the bulk sample are reported

Strain-mediated converse magnetoelectric coupling strength manipulation by a thin titanium layer

The manipulation of the strain-mediated magnetoelectric (ME) coupling strength is investigated by inserting a thin Ti layer (0-10 nm) between a 50 nm Co50Fe50 layer and a (011) oriented lead magnesium niobate-lead titanate (PMN-PT) substrate. A record high remanence ratio (Mr/Ms) tunability of 100% has been demonstrated in the 50 nm CoFe/8 nm Ti/PMN-PT heterostructure, when a total in-plane piezoelectric strain of -1821 ppm was applied at an electric field (E-field) of 16 kV/cm. The ME coupling strength is gradually optimized as the Ti layer thickness increases. Magnetic energy calculation showed that with increasing Ti layer thickness the uniaxial magnetic anisotropy energy (Euni) was reduced from 43 ± 1 kJ/m3 to 29.8 ± 1 kJ/m3. The reduction of Euni makes the strain effect dominant in the total magnetic energy, thus gives an obvious enhanced ME coupling strength

Bird-Like Anatomy, Posture, and Behavior Revealed by an Early Jurassic Theropod Dinosaur Resting Trace

BACKGROUND: Fossil tracks made by non-avian theropod dinosaurs commonly reflect the habitual bipedal stance retained in living birds. Only rarely-captured behaviors, such as crouching, might create impressions made by the hands. Such tracks provide valuable information concerning the often poorly understood functional morphology of the early theropod forelimb. METHODOLOGY/PRINCIPAL FINDINGS: Here we describe a well-preserved theropod trackway in a Lower Jurassic ( approximately 198 million-year-old) lacustrine beach sandstone in the Whitmore Point Member of the Moenave Formation in southwestern Utah. The trackway consists of prints of typical morphology, intermittent tail drags and, unusually, traces made by the animal resting on the substrate in a posture very similar to modern birds. The resting trace includes symmetrical pes impressions and well-defined impressions made by both hands, the tail, and the ischial callosity. CONCLUSIONS/SIGNIFICANCE: The manus impressions corroborate that early theropods, like later birds, held their palms facing medially, in contrast to manus prints previously attributed to theropods that have forward-pointing digits. Both the symmetrical resting posture and the medially-facing palms therefore evolved by the Early Jurassic, much earlier in the theropod lineage than previously recognized, and may characterize all theropods

Nesting probabilistic programs

We formalize the notion of nesting probabilistic programming queries and investigate the resulting statistical implications. We demonstrate that while query nesting allows the definition of models which could not otherwise be expressed, such as those involving agents reasoning about other agents, existing systems take approaches which lead to inconsistent estimates. We show how to correct this by delineating possible ways one might want to nest queries and asserting the respective conditions required for convergence. We further introduce a new online nested Monte Carlo estimator that makes it substantially easier to ensure these conditions are met, thereby providing a simple framework for designing statistically correct inference engines. We prove the correctness of this online estimator and show that, when using the recommended setup, its asymptotic variance is always better than that of the equivalent fixed estimator, while its bias is always within a factor of two